Dio 2 AF27 / AF28
Honda Elite / Dio Starter Package
$ 472.49 $ 478.42
Starter kit for your Elite / Dio Get ready for spring and summer time with this exclusively priced and limited kit! Please contact us if you need 4mm jets for...
NCY race ignition rotor kit Elite dio ZX50
$ 301.99
Here is a simple, no guessing way to make your bike rev out much quicker. This NCY mini mag kit makes a massive difference in throttle response, and how fast...
Elite / DIO AF16 - AF18 "Sport" 72cc Package
Sold Out
Here is a GREAT setup we've taken the time to put together. This is a package put together for the person looking for a reliable, simple, quiet bike. This will...
Motul 800 Synthetic 2 Stroke Oil
$ 29.99
Motul 800 is an ester based high performance engine oil. This oil is made from special oil acids and alcohols. The high fat content of ester oil reduces friction. The...
Maxima 927 Castor 2T Oil 1L
$ 29.49
Maxima 927 2T oil for your ride. This is for PREMIX only.
Fuel can 1 gallon underseat
$ 32.59
Underseat extra fuel solution for the Honda Elite/Dio. This one gallon tank, nearly doubles your fuel capacity. It's also great for when you, or your buddies run out of fuel....
Polini CP Carburetor 15-23mm
$ 167.99
Brand new Polini CP carbs. These are NOT Dellorto clones, this is a completely new designed carb by polini in 15, 17, 19, 21, 23. These use the same hex...
Elite Upgear Kit
$ 59.99
When doing a big bore kit, you need gears. Without them you are never going to take advantage of the extra power. Choose whichever set fits your needs. I suggest...
Stage6 Torque control clutch springs
$ 20.99
Clutch springs should be checked and replaced on a regular basis. Their job is to shift clutch engagement point to higher rpm to improve acceleration and take-off. Stage6 Clutch Springs...
NCY Banjo Bolt With Build In Bleeder
$ 15.99
Hydraulic banjo bolt with bleeder valve. Supplied with two sealing washers. When doing a disk conversion in tight quarters, these bolts allow for easy access to bleed your system. Sold...
NCY 12mm Electroplated Nuts
$ 25.99
12mm axle nuts! These can be used on several different bikes, in several areas. Use them on axle nuts, or cvt parts! M12x1.25 Thread CHECK WHAT YOU HAVE!!! Sold as...
DIO ZX / Genuine 2t / GY6 50cc Adjustable Pulley
$ 42.49
Tired of your bike falling off the powerband after installing that sweet tuned pipe? NCY has your back! This pulley has two different profiles to choose from for fine tuning....
NCY slammed caliper
$ 269.99
MASSIVE 4 piston slammed caliper from NCY, for your build! These work with the NCY slammed caliper adapter, for your Ruckus, Met, Dio or any forks with the proper adapter....
Malossi wing bell
$ 154.39
If your clutch bell has turned blue or has a worn interior the friction plates will not be lasting as long as they should do. If it is out of...
Polini PWK Rebuild Parts
$ 6.99
Over time some parts inside your carb can wear out, gaskets get pinched, things get lost etc. We have compiled the most common replacement parts needed for your PWK carb!...
Cooling Fan Scoop Minarelli
$ 18.89
Need some extra cooling on your performance build? too inexpensive not to buy this little guy. This scoop may require trimming depending on the application. If you built your bike,...
70/94cc Malossi RC-ONE engine KIT
$ 4,413.69
It's hard to beat the Malossi kits. These come with everything you need, to assemble a turn key, bolt in powerhouse. Choose from 94cc or 70cc, Minarelli/Zuma fitment, or Piaggio....
Arrow Exhaust For Honda Elite '94+ and Dio zx50 dd50
Sold Out
Due to a 50% price increase, and tariff, we can't justify bringing these in anymore. We recommend the s23 race pipe, or the F2R
Billet Oil Delete Plug
$ 16.79
Simply remove your oil pump, and install this puppy. Not only do you eliminate the risk for pump failure, you also raise crankcase compression. This kit should be installed on...
Clutch holding tool
$ 38.49
Universal tool for holding clutch or variator. super easy to use, and a great tool to have in your toolbox.
S23 10/12mm Axle Shim Kit Reducer
$ 18.89
I've ran into the issue myself many times, and this should have been done long ago. If you have 12mm legs, this allows you to run a 10mm axle. CNC...
S23 Billet Alum Axle Spacer
$ 11.79 $ 20.99
How many times have you needed a axle spacer, but can't find the right one? This is 12mm or 10mm ID, 20mm OD, same as oem fitment. 3" total length,...
Crank Installation Tools
$ 65.99
Ok, so most of know, that a press/mallet/hammer is the incorrect way to install a crank. And its also the incorrect way to remove a crank. Cranks are not designed...
Fuel or Oil Line Clamp
$ 23.29
Hose clamp tool is awesome for keeping the fuel and oil mess to a minimum. Clamp this guy to your carb fuel line, oil injection line, or whatever you want,...